Speed Queen Parts

Fix Number: FIX334310
Manufacturer Part Number: 279834

This OEM kit comes with two ignition coils (one three-terminal boost/hold coil, and one two-terminal secondary coil). Usually only one of them burns out, but you should replace them as a set as both have to be operational for the gas valve to open. The primary purpose of the part is to open the gas valve and allow the gas to enter the burner. This is a safety mechanism to make sure that there is never an unsafe buildup of gas inside the appliance. You will find the coils attached to the dryer gas valve. This is not an uncommon repair; it can fail due to normal material fatigue over time. To test your current parts, watch the burner, and if the igniter glows for a while and then shuts off without the gas is igniting, it usually means one of these coils is bad.

Fixes these symptoms

Noisy
Not Heating
See more...

Installation Instructions

Dennis from ALISO VIEJO, CA

Dryer ran but did not dry clothing.

Best site I have ever used for repairs. First a list of what parts were needed was provided right from the start, no guessing. I followed all of the video's provided for installation instructions and and that was it. Very easy to make repairs and almost rebuilt my dated dryer to like new condition. Appliance was in very good physical condition just needed new components to bring it back. Highly recommend this site to anyone who can turn a wrench. Read more...

Affresh Washing Machine Cleaner - 3 pack

$12.58

Fix Number: FIX1960673
Manufacturer Part Number: W10135699

This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.

Drum Support Roller

$20.93

Fix Number: FIX11741913
Manufacturer Part Number: WP37001042

If your dryer is not tumbling, takes a long time to dry, or is noisy while tumbling, it may be time to replace the drum support rollers. These hold the drum in place while it rotates, so if they have become worn it can make for a lot of noise while the machine is operating. This genuine OEM part is sold individually, however your dryer will have two support rollers. As they tend to wear at the same rate, we suggest replacing both at the same time. The tools needed to complete this repair include a putty knife, 5/16 nut driver, and a pair of pliers. Completing this repair requires removing the drum from the dryer to access the support rollers. Be sure to disconnect power to the appliance before beginning this repair.

Fixes these symptoms

Noisy
See more...

Installation Instructions

Rachel from Berrien Center, MI

Drum was not working properly

It was very easy to installed new parts. Read more...

Dryer Radiant Flame Sensor

$47.87

Fix Number: FIX11741429
Manufacturer Part Number: WP338906

This genuine OEM part is a radiant flame sensor for your gas dryer. It is used to determine when the temperature of the igniter is hot enough to ignite the gas. Once the igniter is hot enough, it allows the valve to open to release the gas. This acts as a safety mechanism which prevents dangerous levels of gas from building up. If your dryer will not start, is not producing enough heat, not heating up at all, is taking too long to dry laundry, or is shutting off too soon, you may need to replace the radiant flame sensor. Please be sure to disconnect the power and gas supply to your dryer before beginning this repair.

Fixes these symptoms

Not Heating
See more...

Installation Instructions

William from Corsicana, TX

Oor dryer would not get hot.

I opened the bottom section and watched as the igniter got red hot as it should but the gas valve did not open. I wired around the sensor and the gas valve opened and the fuel ignited. VERY IMPORTANT: DO NOT RUN YOUR DRYER IN THIS STATE: IT WILL BLOW UP!! I did a VERY short test, then ordered the new sensor. Just one screw holds the sensor (as shown in the Parts video). One screw out, new sensor, one screw in and our dryer is back in full and proper running order. Read more...

Drum Glide

$14.16

Fix Number: FIX11741931
Manufacturer Part Number: WP37001298

Located in the front bulkhead of your dryer are two drum glides, which help to ensure that the drum rotates smoothly and quietly while the dryer is operating. When the glides wear down, it can cause a metal-on-metal noise while the machine is tumbling. If you notice that your dryer is excessively noisy, is not tumbling, or is leaving marks on your clothes, it may be time to replace the glides. This genuine OEM part is sold individually, however we recommend replacing both glides at the same time to ensure even wear. Please be sure to disconnect the power supply to the dryer before beginning this repair.

Fixes these symptoms

Marks left on clothes
Noisy
See more...

Installation Instructions

Rachel from Berrien Center, MI

Drum was not working properly

It was very easy to installed new parts. Read more...

Dryer Idler Assembly

$35.66

Fix Number: FIX11741930
Manufacturer Part Number: WP37001287

The spring for this part is sold separately. This idler assembly is for dryers. Idler assembly includes the idler arm and the idler pulley that maintains tension on the drive belt, allowing the belt to turn. Disconnect the power before installing this part. Wear work gloves to protect your hands.

Fixes these symptoms

Drum Not Spinning
Noisy
See more...

Installation Instructions

Rachel from Berrien Center, MI

Drum was not working properly

It was very easy to installed new parts. Read more...

Thrust Washer

$7.95

Fix Number: FIX11740482
Manufacturer Part Number: WP233520

This washer is 3/4 inches in diameter.

Fixes these symptoms

Burning smell
Noisy
Spins slowly
See more...

Installation Instructions

Ralph from Alexandria, OH

Grinding , drum flopping , .....Noise !

I won't go into all the details of the repairs .....The videos this company provides are A+++.. Some would say I would have been better off purchasing a New dryer ...LOL if I had to use a appliance repair man for this job ...Probably ...but ...using this site certified parts , and using the easy to follow instruction videos ....It was truly a very easy repair . I spent more time getting everything perfectly clean inside the dryer housing ,and letting the high temp adhesive cure than I did actually installing the parts.I can't recommend this company or the parts more ...Just take your time with removal , cleaning , and installation ....Patience !Excellent ...parts quality , shipping speed , and video installation instructions !!!! My dryer now works and SOUNDS like a new dryer ....Thank you ! Read more...

Water Inlet Valve

$98.35

Fix Number: FIX1583805
Manufacturer Part Number: 205613

This part has two ports for water to enter. It is blue and is intended for use with many washing machines and comes with a multi-mount bracket and an outlet adaptor.

Fixes these symptoms

Leaking
No hot or cold water
Water Filling Issues
See more...

Installation Instructions

Conrad from Chesapeake, VA

The Cold water inlet was down to a trickle

The other given instructions are good, except I would add 2 more things to do. Also the valve comes with written instructions, but they are somewhat incomplete. 1. before disassembly & removal look at the valve assembly and note its orientation. Inlet valve at the top. Make sure your hot and cold hoses are correctly identified and I marked the hot and cold inlet, BEFORE I removed the hoses. You don't want to get them mixed up. 2. even more important note the color coded wires that attach to the top and bottom contacts. I marked the valve assembly with the 1st letter of the color of the wire that is attached to each contact. My Maytag is over 30 years old & this is the 1st problem that I had with it. The new valve works perfectly. Read more...