Whirlpool Mixer Parts

Start With Your Model Number

Need help finding your model number?
Find Parts Fast
Guaranteed Fit
Repair Videos
Fix.com search
Whirlpool Appliance Parts
Shop By Appliance Type Shop By Part Type

Popular Whirlpool Mixer Parts

Watch the install video
Worm Gear – Part Number: WPW10112253
Worm Gear
$20.97
In Stock
★★★★★
★★★★★
8 Reviews
Fix Number
FIX11748374
Manufacturer Part Number
WPW10112253
This part includes one worm gear for a stand mixer. It measures approximately 1.5-inches in diameter and is sourced directly from the manufacturer. The worm gear is responsible for turning the planetary where the accessories attach. A few common reasons for replacing this part include, unusual sounds (grinding) or if it will not start.
Fixes these symptoms

Installation Instructions

Melody from Silverton, CO
stripped the worm gear, fixed bushings
I opened the mixer and determined that the worm gear had failed, as designed, to save the other gears. There was also oil separated from the grease and it needed replaced. The Transmission case gasket was damaged and must have been from the time it was built. I removed the grease with putty knife and kept I on a plastic plate until the parts came in (to determine the amount needed when I replaced it.) I used the punch to remove the two pins needed with light tap from hammer. I left the mixer in pieces on the counter until the parts arrived. I replaced the gear and all other parts and placed fresh grease in the mixer. I had to adjust the beater, too. I had removed one of the bushings by mistake. When mixer was back together it would not start. IT TOOK SOME TIME BUT I FOUND ANOTHER WEB SITE THAT EXPLAINED HOW TO REPLACE THE BUSHING. TAKE A FLASHLIGHT AND LOOK INTO THE SQUARE BRUSH HOLDER. THERE IS A DETANT IN THE HOLDER. THE SHAVED SIDE OF THE BRUSH NEEDS TO SLIP PAST THE DETENT TO BE ABLE TO TOUCH THE AMATURE. Once that was done, it worked great. Very smooth with new gear and grease. Read more...
Watch the install video
Retaining Ring – Part Number: WP9703438
Retaining Ring
$7.87
In Stock
Fix Number
FIX11746909
Manufacturer Part Number
WP9703438
Sometimes referred to as a retaining clip, the retaining ring is used to hold the drum support roller onto the shaft in your dryer. The clip may need to be replaced if you find that your dryer is noisy while tumbling or will not tumble at all. The retaining clip can also be used with stand mixers, to hold the pinion gear to the agitator shaft. This genuine OEM part is made entirely out of metal and measures approximately half an inch in diameter.
Fixes these symptoms

Installation Instructions

Brian from Novi, MI
Squeaking noises while running dryer
Followed the Video Directions from website. All went as planed. The dryer is running like new now. Read more...
Worm Following Gear – Part Number: W11086780
Worm Following Gear
$18.28
In Stock
★★★★★
★★★★★
3 Reviews
Fix Number
FIX12070620
Manufacturer Part Number
W11086780
This is a genuine OEM worm following gear for your stand-up mixer. The gear is made of metal and is attached to the planetary shaft. This is an important part of the appliance as it helps to drive the beaters for your mixer. Over time, the teeth on the gear can become stripped or worn down, and it will need to be replaced. Signs that you may need to replace this gear are if the mixer is not spinning, or if it making excessive noise. Please be sure to unplug the mixer before beginning this repair.
Fixes these symptoms

Installation Instructions

carol from whittaker, MI
mixer skipped while turning
followed instructional video the hardest part was removing the snap ring! once that was removed it was a piece of cake! Read more...
Watch the install video
Worm Gear and Bracket – Part Number: WP240309-2
Worm Gear and Bracket
$36.52
In Stock
★★★★★
★★★★★
4 Reviews
Fix Number
FIX11740516
Manufacturer Part Number
WP240309-2
Used for Kitchenaid Mixers.
Fixes these symptoms

Installation Instructions

James from Windsor, NY
Internal Worm Gear to Electric Motor Stripped
After looking at your sites great exploded views I was able to disassemble the motor assembly. Replaced the brushes and damaged gear assembly . Reassembled Worked great.Wife's china made mixer had diecast internal parts that shattered after her attempt to mix cookie dough. Now with this USA made Kitchen Aid Mixer she can mix concrete with coke bottles and never work hard. Thank You for you great site and delivery ethic. Only wish my Hitachi ex50urg excavator had a parts exploded views as you do. Also Worm gear and bracket had improvements to redirect lube grease to keep improved gear material well lubricated. Read more...
Watch the install video
Motor Brush – Part Number: WPW10380496
Motor Brush
$13.51
In Stock
Fix Number
FIX11753983
Manufacturer Part Number
WPW10380496
This genuine OEM part is a motor brush for your stand mixer. The brush is sold individually, however, there are two motor brushes on your mixer, and we recommend replacing both at the same time, as they tend to wear out at the same rate. A sign that you may need to replace the brushes is if your mixer is running slowly. A flat blade screwdriver is needed to remove the brush cover in order to replace this part.
Fixes these symptoms

Installation Instructions

James from Windsor, NY
Internal Worm Gear to Electric Motor Stripped
After looking at your sites great exploded views I was able to disassemble the motor assembly. Replaced the brushes and damaged gear assembly . Reassembled Worked great.Wife's china made mixer had diecast internal parts that shattered after her attempt to mix cookie dough. Now with this USA made Kitchen Aid Mixer she can mix concrete with coke bottles and never work hard. Thank You for you great site and delivery ethic. Only wish my Hitachi ex50urg excavator had a parts exploded views as you do. Also Worm gear and bracket had improvements to redirect lube grease to keep improved gear material well lubricated. Read more...
Hub Gear – Part Number: W11192795
Hub Gear
$22.07
In Stock
★★★★★
★★★★★
4 Reviews
Fix Number
FIX12348886
Manufacturer Part Number
W11192795
This hub gear is a genuine OEM replacement part for your stand mixer. This kit includes both the beveled gear and attachment and is also referred to as a worm follower gear. This gear assists with the rotation of the planetary assembly in the mixer. If the teeth of the gear have worn out, or nothing rotates when the mixer is turned on, you may need to replace the hub gear.
Fixes these symptoms

Installation Instructions

Bob from NORTH AUGUSTA, SC
The mixer would not spin.
Took the cover off of the transmission and replaced gears, pin and gasket and added new grease. Read more...
Worm Gear – Part Number: WP9709231
Worm Gear
$48.07
In Stock
Fix Number
FIX11747012
Manufacturer Part Number
WP9709231
Sold individually.
Fixes these symptoms

Installation Instructions

Dan from Forest Grove, OR
Damaged gears
Watched the video several times. Once I received the parts, I watched it again to see specific sections. Repair was easy when I knew what to expect. It would help if the video could be in sections, so you would not have to watch the entire beginning in order to see later instructions. Also found the parts manual on line and ordering of parts was very easy and processed correctly by your company. Really appreciated your help. Read more...
Watch the install video
Stand Mixer Speed Control Board and Knob (Black) – Part Number: WP9706648
Stand Mixer Speed Control Board and Knob (Black)
$87.44
In Stock
★★★★★
★★★★★
3 Reviews
Fix Number
FIX11746947
Manufacturer Part Number
WP9706648
This assembly includes the black knob. Used with Stand Mixers.
Fixes these symptoms

Installation Instructions

Barbara from La Grange, CA
switch was intermittent
followed instructions from your web sight. the most important part is to make sure you put the wiring on the proper connection. the board was wired a little different than the original. Read more...
Watch the install video
Flat Beater – Part Number: WPW10672617
Flat Beater
$26.95
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX11757063
Manufacturer Part Number
WPW10672617
This flat beater is a genuine OEM part for your stand mixer. If your beater has become worn out or is missing, this is the replacement you need. The beater is white in color and has a powder coated finish. We recommend hand washing this part, as the coating can wear faster if you are using the dishwasher. No tools are required, simply swap out the beater like you would with any of the mixer attachments.
Fixes these symptoms

Installation Instructions

Jeptha from CHANUTE, KS
Covering had worn off the beater
Snap it in place, less than a minute Read more...
Retaining Pin – Part Number: WP9707223
Retaining Pin
$9.02
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX11746974
Manufacturer Part Number
WP9707223
This part works in conjunction with the worm and bevel gear.

Installation Instructions

Bob from NORTH AUGUSTA, SC
The mixer would not spin.
Took the cover off of the transmission and replaced gears, pin and gasket and added new grease. Read more...

Whirlpool Mixer Appliance Types

Related Whirlpool Mixer Parts

Popular Whirlpool Mixer Models

View More
+