OEM Milwaukee Reciprocating Saw Parts & Accessories

Shoe Assembly

$15.57

Fix Number: FIX10132586
Manufacturer Part Number: 45-16-0645

The shoe assembly is located at the front of the reciprocating saw and helps to direct the blade while you cut. The most common reason this part is replaced is just from simply misplacing it. If the saw is used roughly, the pivot hinge between the mounting bar and the shoe can damage, which can cause the shoe to fall off. Never use your saw without this part intact as it could cause damage to your equipment. For this easy repair, use your Allen wrench to remove the screws and this will allow you to remove the shoe. To install the new shoe assembly, line up the forks with the housing and slide it into position. To finish, tighten the screws back up and it is ready to go.

Carbon Brush Assembly

$3.99

Fix Number: FIX10122278
Manufacturer Part Number: 22-20-0065

This is an OEM carbon brush assembly for a saw, sold as one part. It includes one metal brush holder with spring and one carbon brush with a lead wire attached. It is highly recommended to replace both the carbon brushes at the same time to ensure even wear and optimal performance. For this quick and easy replacement, you will need a screwdriver. Remove the screws securing the cover, remove the two halves of the housing, remove the old carbon brush assembly, and place the new one in its place.

Brush Holder Assembly

$3.99

★★★★★

2 Reviews

Fix Number: FIX10122311
Manufacturer Part Number: 22-20-0535

This part includes one brush and holder. Your tool likely requires two brushes, so please order accordingly, as it is always advised to replace both brushes at the same time. If you are experiencing an inconsistent motor or one that does not work at all, a lot of times this is due to worn brushes. This is a very common repair, so we recommend inspecting them regularly. If burns or smoking are present, be sure to check the armature as well.

Shoe Assembly

$5.89

Fix Number: FIX10132558
Manufacturer Part Number: 45-16-0030

This part includes one OEM shoe assembly for a reciprocating saw. The shoe assembly gives support while your tool is operating by acting as a spacer/stop. It also assists in limiting vibration and kickback. This part is commonly replaced because it gets lost. When it is used roughly, the pivot hinge between the mounting bar and the shoe assembly can break and this can cause the shoe assembly to fall off. For this repair you will need a torx screwdriver. Start by removing the screws that hold the shoe assembly to the housing, remove the old shoe, and secure the new shoe with the two screws.

Watch the install video

Carbon Brush (Sold Individually)

$4.99

Fix Number: FIX10122113
Manufacturer Part Number: 22-16-0275

This is a carbon brush, it is also known as a motor brush, and it is used with various power tools and equipment. The brush transfers electric currents to the motor. Your motor brush is an extremely common replacement part. It is considered a wear part, because the constant friction will wear it down. If you are experiencing a poor running motor, you will need to replace this part. New brushes will restore your motors electric braking. We recommend also inspecting your armature for damaging cracks or burns, this can indicate a larger problem in your motor that will require attention.

10-24 X 1/2" Pan HD. Sit. Tapt. T-25

$4.99

Fix Number: FIX10118952
Manufacturer Part Number: 06-82-5314

This part includes one pan head torx screw. It is sourced directly from the original manufacturer, ensuring a premium high-quality screw. It is compatible with a variety of equipment, so will serve various applications. It measures 10-24 by 1/2. Be sure to use the appropriate size tool to loosen and tighten it so it does not get damaged.

Carbon Brush & Spring

$4.99

Fix Number: FIX10122225
Manufacturer Part Number: 22-18-0910

Designed for use with select Milwaukee tools, this OEM approved replacement Brush fits a variety of models. To see if this part will fit your tool, please see the "Model Cross Reference List" below. This brush is made out of a durable carbon alloy, has a lead wire and spring attached to it, and its primary purpose is to conduct electrical current from the stationary wires to the moving parts of your tool. Brushes are one of the most commonly replaced power tool parts because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common cause of intermittent motor function, reduced electric braking, and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. Brushes are sold individually, and might also be known as Carbon Brushes or Motor Brushes. It is recommended to replace both brushes, even if only one is worn.

Installation Instructions

Bob from OCONOMOWOC, WI

None

Remove the retaining screw, remove old brush and spring, install new brush and spring, reinstall retaining screw. Repeat for the second brush and spring. Read more...

Pin-Shoe

$4.99

★★★★★

1 Review

Fix Number: FIX10131365
Manufacturer Part Number: 44-60-1635

This is an individually sold metal shoe pin for a reciprocating saw. It holds the shoe retainer in place. For this repair you will need a screwdriver and pliers.

Quik-Lok Power Cord Set

$43.96

Fix Number: FIX10134042
Manufacturer Part Number: 48-76-4008

This Milwaukee Quik-Lok® cord is a genuine OEM replacement part, it is sold individually. This is a three wire grounded 8 foot cord for fast field replacement of a damaged cord. Made of premium grade Hi-Flex wire the cord is quickly removed and attached to Milwaukee tools with the Quik-Lok® cord feature. To change a damaged cord simply turn the collar at the top of the cord counter clockwise to loosen the nut and pull down on the cord to remove. To re-attach a new cord, line up the pins in the end of the tool with the pin receptacles in the end of the cord, push together and turn the collar clockwise to lock in place. The Cord has a 5-15P NEMA type plug.

Installation Instructions

Brian from ATHENS, AL

Had a bad cord

Insert end turned to the right. Done. Read more...

Watch the install video

Shoe Release Lever

$5.19

Fix Number: FIX10126092
Manufacturer Part Number: 31-52-0090

This shoe release lever is sourced directly from the original manufacturer, ensuring an exact replacement for your saw. The shoe release lever can be adjusted forwards or backwards to account for the part of the blade not being used or for instances when you need a low blade clearance. This part is sold individually.

Installation Instructions

William from LEESBURG, FL

Replaced sawzall shoe handle lock

Popped it on Read more...

Milwaukee Reciprocating Saw Parts

Popular Milwaukee Reciprocating Saw Parts

Installation Instructions

Installation Instructions

Installation Instructions

Milwaukee Reciprocating Saw Appliance Types

Popular Milwaukee Reciprocating Saw Models

Milwaukee Reciprocating Saw Parts

Start With Your Model Number

Popular Milwaukee Reciprocating Saw Parts

Installation Instructions

Installation Instructions

Installation Instructions

Milwaukee Reciprocating Saw Appliance Types

Popular Milwaukee Reciprocating Saw Models