OEM Delta Band Saw Parts & Accessories

Carbon Brush (Sold Individually)

$10.69

Fix Number: FIX10176277
Manufacturer Part Number: 5140011-85

This is a single carbon brush with a spring. Carbon brushes are what supply electricity to the armature. They are known to wear due to constant rubbing against the commutator, so it should not be a concern if they are in need of a replacement. They should be inspected regularly, especially if your power tool is not functioning properly. A worn brush can cause excessive sparks, however a damaged armature can also cause sparks, so you will need to inspect both parts. This is a simple repair that should only take a few minutes. You will need to remove the brush caps, and then align the new carbon brush in the holder with the tabs. You will need a screwdriver to secure the cap.

Switch W/ Key

$41.51

★★★★★

10 Reviews

Fix Number: FIX10325609
Manufacturer Part Number: 489105-00

This Switch is an OEM approved replacement part for various tools and models manufactured by Delta, Black and Decker, and Porter Cable. For full compatibility, please see the "Model Cross Reference List" below. This Switch has four terminals, a removable safety key, and a compact design for easy installation. The purpose of the switch is to turn the device on/off, as well as playing a role in electric breaking by momentarily reversing electrical polarity. Due to the mechanical internals of switches, they tend to degrade and wear out over time, making them a commonly replaced part in power tools. Common symptoms of a broken switch include: the device has completely stopped functioning, it will not turn on, and turning off intermittently during use. Each Switch is sold individually, and may also be referred to as a Rocker Switch.

Installation Instructions

keith from EMPORIA, KS

Power switch would not turn saw off

unplugged power cord.
removed the nut holding the power switch assembly on the saw.
removed 3 screws from the back cover.
removed the 2 white wires and 2 black wires from the switch terminal post. pay attention to wire color on each post.
removed old switch from the bracket by squeezing the sides of the old switch to remove the switch from the bracket.
inserted the new switch in place in the opening.
re attached the wires to the spade terminal on the switch using the 4 terminals. black on the 2 posts top and bottom on one side and the other side white on the top and bottom.
re attach the switch assembly to the table saw
test operation Read more...

Tire

$93.42

Fix Number: FIX10328595
Manufacturer Part Number: 905145

This is a genuine part that is supplied by the original equipment manufacturer for use with Delta band saws. The tire is one of the most important parts, its purpose is to help track the blade on the wheel. If the tire becomes stretched or starts cracking you will notice your blades not tracking properly. Keep in mind this high-quality component is made of durable rubber material and is sold individually. Please make sure to refer to the owners manual for the correct application of this tire.

Installation Instructions

Frank from MOUNT IDA, AR

installing "Tire on drive wheel

Had to have another individual to help. It takes 4 hands to install! Read more...

Trunnion

$12.24

★★★★★

3 Reviews

Fix Number: FIX10323810
Manufacturer Part Number: 426020950002S

Installation Instructions

Kenny from LAYTON, UT

Broken trunnions when trying to move bandsaw by lifting on table, not a good practice!!

Remove broken trunnions, fit new ones into place and tighten. Then mount on saw and if movements are hard or impossible, remove table top, and trunnions , and using a bench grinder remove molding marks from bolt retainers inside of trunnions. (Be careful not to let the grinder take the brackets out of your hands). Reassemble and try again. Read more...

Bearing

$3.99

Fix Number: FIX10331441
Manufacturer Part Number: DPEC001399

Bearing

$51.91

Fix Number: FIX10315390
Manufacturer Part Number: 1086894S

This ball bearing fits a variety of lawn and gardening tools. The ball bearings prevent friction between rotating parts. The balls do this by bearing the load and spin and distributing the weight equally, while the minimal contact area of the balls reduce friction. This allows your tool to run easily. Ball bearings are a commonly replaced part because of the constant wear they experience. Tip: check your bearings and replace them periodically. *Please note: they are sold individually.

Table Insert

$41.51

★★★★★

2 Reviews

Fix Number: FIX10323790
Manufacturer Part Number: 426020630001S

This is a table insert plate for your saw. It is attached to the table, and provides access to the blade. A table insert protects the rest of the unit by preventing wood from getting jammed under the blade during cutting. The slit in the insert plate allows for the saw blade to run smoothly. Before installing this part, unplug your saw.

Bearing

$29.06

★★★★★

1 Review

Fix Number: FIX10329705
Manufacturer Part Number: 920080201457S

Key

$10.37

Fix Number: FIX10318424
Manufacturer Part Number: 1343758

This safety key fits multiple hardware tools and is inserted into the switch to make it possible for your machine to turn on and operate. Tip: you can remove the key to prevent unauthorized use of the machine. For installation instructions refer to the diagram provided by the manufacturer.

Table Insert

$3.99

Fix Number: FIX10331503
Manufacturer Part Number: DPEC001462

Delta Band Saw Parts

Popular Delta Band Saw Parts

Installation Instructions

Installation Instructions

Installation Instructions

Delta Band Saw Appliance Types

Related Delta Band Saw Parts

Popular Delta Band Saw Models

Delta Band Saw Parts

Start With Your Model Number

Popular Delta Band Saw Parts

Installation Instructions

Installation Instructions

Installation Instructions

Delta Band Saw Appliance Types

Related Delta Band Saw Parts

Popular Delta Band Saw Models