OEM Milwaukee Electric Drill Parts & Accessories

Carbon Brush Assembly

$5.19

Fix Number: FIX10122192
Manufacturer Part Number: 22-18-0680

This carbon brush is used on a variety of cordless tools and appliances. *Please note: This part is sold individually. Carbon brushes are commonly replaced because they wear out easily with friction. If your brush is worn out it can cause disruption in the functioning of the motor and reduce electric braking. If you notice cracks, burns and other damage on wire lead, then it is best to replace it to restore the motor and its functions. Refer to the manual provided by the manufacturer for further installation instructions.

Brush Assembly (2 Required)

$9.81

Fix Number: FIX10122258
Manufacturer Part Number: 22-18-1310

This is a single carbon brush, and it is compatible with various types of equipment. Although it is sold individually, it is always recommended to replace both carbon brushes are the same time, even if only one appears worn. Properly maintaining the carbon brushes will ensure your motor runs consistently smooth, protecting the longevity of your equipment. Take this opportunity to also inspect the armature, especially if sparks are present.

Carbon Brush/Spring (2 Required)

$20.53

Fix Number: FIX10122196
Manufacturer Part Number: 22-18-0702

This part includes one authentically sourced carbon brush with the wire lead and spring attached. This part is sold individually, however it is always recommended to replace both carbon brushes at the same time. Carbon brushes wear down with regular use of your tool, so to keep it running smoothly they need to be replaced on a regular schedule, or earlier if your motor is not performing. During the inspection of your carbon brushes also check the condition of the armature.

Carbon Brush/Spring (2 Required)

$10.07

Fix Number: FIX10122195
Manufacturer Part Number: 22-18-0701

This is an OEM carbon brush, sold individually. Your tool will require two of these, so please be sure to order what you need. It is best practice to replace both carbon brushes at the same time, even if only one appears worn. Worn brushes are a common reason for a malfunctioning motor, so it is important to inspect them regularly and replace them when needed. When you are inspecting the carbon brushes look for wear near the wire lead. If there are burns, this could be an indication that something is also wrong with the armature, so it should be checked as well.

Watch the install video

Carbon Brush (Sold Individually)

$4.99

Fix Number: FIX10122113
Manufacturer Part Number: 22-16-0275

This is a carbon brush, it is also known as a motor brush, and it is used with various power tools and equipment. The brush transfers electric currents to the motor. Your motor brush is an extremely common replacement part. It is considered a wear part, because the constant friction will wear it down. If you are experiencing a poor running motor, you will need to replace this part. New brushes will restore your motors electric braking. We recommend also inspecting your armature for damaging cracks or burns, this can indicate a larger problem in your motor that will require attention.

Carbon Brush and Spring (2 Required)

$8.25

Fix Number: FIX10122190
Manufacturer Part Number: 22-18-0670

This part includes one carbon brush with spring. Two of these brushes are needed in most models, and we recommend replacing them both at the same time, as they tend to wear at the same rate. A worn brush often affects the performance of the motor, and that is usually the first indication that a replacement is needed. For this repair, you will need to use a screwdriver to remove the brush cap which holds the brushes in place. To install, align the new brush with the holder and insert it by aligning the wings with the sides of the holder. Press the brush into the holder and secure the cap back on. Never over-tighten the cap, as this could break it. These steps will need to be repeated on the other side for the second brush.

Shear Pin

$4.99

Fix Number: FIX10131201
Manufacturer Part Number: 44-60-0032

This is an authentic shear pin for a drill. This shear pin is sold individually, however we recommend keeping a few extra of these on hand. The shear pin is designed to break at a certain point in order to protect the gears and motor from overloading. If your shear pin has snapped, this is the OEM replacement you will need to fix it.

Carbon Brush & Spring

$4.99

Fix Number: FIX10122225
Manufacturer Part Number: 22-18-0910

Designed for use with select Milwaukee tools, this OEM approved replacement Brush fits a variety of models. To see if this part will fit your tool, please see the "Model Cross Reference List" below. This brush is made out of a durable carbon alloy, has a lead wire and spring attached to it, and its primary purpose is to conduct electrical current from the stationary wires to the moving parts of your tool. Brushes are one of the most commonly replaced power tool parts because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common cause of intermittent motor function, reduced electric braking, and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. Brushes are sold individually, and might also be known as Carbon Brushes or Motor Brushes. It is recommended to replace both brushes, even if only one is worn.

Installation Instructions

Bob from OCONOMOWOC, WI

None

Remove the retaining screw, remove old brush and spring, install new brush and spring, reinstall retaining screw. Repeat for the second brush and spring. Read more...

Keyless Chuck

$30.78

Fix Number: FIX17016934
Manufacturer Part Number: 42-66-2608

Keyless Chuck

Brush Holder Assembly

$8.85

Fix Number: FIX10122286
Manufacturer Part Number: 22-20-0150

This is an authentically sourced OEM brush holder assembly for drills. The assembly includes, the metal brush holder, brush with lead wire and the spring. For most models, this repair will require both brush replacements, so you will may need to order two of these in most cases. Carbon brushes are a common wear component that require regular maintenance.

Milwaukee Electric Drill Parts

Popular Milwaukee Electric Drill Parts

Installation Instructions

Milwaukee Electric Drill Appliance Types

Related Milwaukee Electric Drill Parts

Popular Milwaukee Electric Drill Models

Milwaukee Electric Drill Parts

Start With Your Model Number

Popular Milwaukee Electric Drill Parts

Installation Instructions

Milwaukee Electric Drill Appliance Types

Related Milwaukee Electric Drill Parts

Popular Milwaukee Electric Drill Models