Electric Drill Parts

Popular Electric Drill Parts

Carbon Brush Assembly
$5.19
In Stock
Fix Number
FIX10122192
Manufacturer Part Number
22-18-0680
This carbon brush is used on a variety of cordless tools and appliances. *Please note: This part is sold individually. Carbon brushes are commonly replaced because they wear out easily with friction. If your brush is worn out it can cause disruption in the functioning of the motor and reduce electric braking. If you notice cracks, burns and other damage on wire lead, then it is best to replace it to restore the motor and its functions. Refer to the manual provided by the manufacturer for further installation instructions.
Power Cord
$17.56
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX10169875
Manufacturer Part Number
330072-98
This power cord is used for power tools and some of the following tools: electric drills, reciprocating saws, jig saws, biscuit joiners, and routers. The power cord is made for double insulated tools and is a two-wire cord with two prongs, but it does not need a ground wire. If there are cuts in the cord insulation, intermittent power during operation, or damaged and bent prongs, then replacing the power cord will solve the problem. The tools needed for this repair are a Phillips screwdriver, small screwdriver, wire cutters/strippers, crimping tool, and terminal (ring or spade). Repair tip: During installation, remember that new cord wires must go correctly into wire terminals. Also, to avoid pinching when the tool case is put back into place, remember to route cord and wires in the right path.

Installation Instructions

John from Hancock, MI
Did not come with grinding disc guard
While unit was unplugged I screwed clamp of guard around grinder. Read more...
Carbon Brush Set CB-303
$10.85
In Stock
Fix Number
FIX10156649
Manufacturer Part Number
CB303
The carbon brush is used on a variety of tools and are commonly replaced because they wear out easily with time and use. If your brush is worn out it can affect the motor from working properly and reduce electric braking. Tip: to check if the brush is worn out, inspect the wire lead for cracks, burns and other damage. Refer to the diagram provided by the manufacturer for further installation instructions. *Please note: This part is sold individually. This assembly includes a carbon brush, spring and holder.
Cord Set
$20.72
In Stock
Fix Number
FIX17016229
Manufacturer Part Number
344492750
This is an OEM 16-gauge cord for double insulated tools. It is sold individually, and measures 9 feet long. It is a two-wire cord with two prongs and does not require a ground wire. If the cord is cracked or damaged in any way, it should be replaced right away to avoid shock.
Power Cord
$21.97
In Stock
Fix Number
FIX10153834
Manufacturer Part Number
664064-4
This is a power cord, and it is used with several power tools. It is made of a thick rubber that is tough, and insulated for a long life. It has two 18 gauge wires, and is 8 feet long. When removing your old cord, take note of the wire leads placements, and how they connect to the receptacle in the tool. You will have to attach the new cord similarly.

Installation Instructions

John from Hancock, MI
Did not come with grinding disc guard
While unit was unplugged I screwed clamp of guard around grinder. Read more...
Carbon Brush CB-124 (Set of 2)
$7.83
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX10156640
Manufacturer Part Number
CB124
Carbon brushes are needed to conduct electricity to the armature through the commutator. The brushes are continuously rubbing against the rotating commutator, so will wear down over time, and will need to be replaced. If you are experiencing excessive sparks, this can also be caused by a damaged armature, so it is best to check it at the same time. This part includes two carbon brushes, which need to be replaced at the same time.
Carbon Brush (Sold Individually)
$4.99
In Stock
Fix Number
FIX10167153
Manufacturer Part Number
176846-04
This is a single OEM carbon brush. Two are needed to make a set, so if you require two, order accordingly. Carbon brushes are used to conduct electricity to the armature through its commutator. Brushes are a common wear part that will need to be replaced periodically due to consistent rubbing against the rotating commutator. Worn brushes can cause sparks around the commutator, which can also cause damage to the armature, which should also be inspected. If your electric motor is experiencing issues, the brushes should be one of the first things you check.
Brush Assembly (2 Required)
$9.81
In Stock
Fix Number
FIX10122258
Manufacturer Part Number
22-18-1310
This is a single carbon brush, and it is compatible with various types of equipment. Although it is sold individually, it is always recommended to replace both carbon brushes are the same time, even if only one appears worn. Properly maintaining the carbon brushes will ensure your motor runs consistently smooth, protecting the longevity of your equipment. Take this opportunity to also inspect the armature, especially if sparks are present.
Carbon Brush/Spring (2 Required)
$20.53
In Stock
Fix Number
FIX10122196
Manufacturer Part Number
22-18-0702
This part includes one authentically sourced carbon brush with the wire lead and spring attached. This part is sold individually, however it is always recommended to replace both carbon brushes at the same time. Carbon brushes wear down with regular use of your tool, so to keep it running smoothly they need to be replaced on a regular schedule, or earlier if your motor is not performing. During the inspection of your carbon brushes also check the condition of the armature.
Fix Number
FIX10156656
Manufacturer Part Number
CB407
This set comes with two carbon brushes with wire leads and brush strings attached. If your motor is not running efficiently or is operating intermittently, this is a common sign of worn brushes. Due to the friction they are constantly under, they will wear over time, and will start to appear cracked, pitted, or burnt if not replaced regularly. We recommend also taking a look at the armature to ensure it is not damaged. This brush set is compatible with multiple model types, so it is best to consult your user manual for repair instructions.

Electric Drill Brands

Related Electric Drill Parts

Popular Electric Drill Models