OEM Makita Parts & Accessories

Carbon Brush Set

$14.14

Fix Number: FIX10156653
Manufacturer Part Number: CB340

Set of 2 Carbon Brushes with wire leads and brush springs attached. The set contains genuine Makita replacement parts, and comes packaged in a Makita retail box. rnThis brush set will fit the Makita tools listed at the bottom of the page. • Worn brushes frequently are the cause behind a motor running poorly. • Replacing brushes can fix a motor that’s operating intermittently. • New brushes can restore a motor’s electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

Carbon Brush Set

$10.85

Fix Number: FIX10156641
Manufacturer Part Number: CB154

This motor brush set is for power tools. Motor brush set transfers electric current to the spinning armature in the motor. The set includes both motor brushes.

Watch the install video

Carbon Brush Set CB-325

$6.19

Fix Number: FIX10156652
Manufacturer Part Number: CB325

Watch the install video

Drain Valve

$4.99

★★★★★

1 Review

Fix Number: FIX10049094
Manufacturer Part Number: N286039

This is a single OEM drain valve for an air compressor. A drain valve is a small device that is usually located at the bottom of the compressor air receiver. The drain valve can be opened or closed, and this allows water to exit the tank. Water builds up if air is left in the tank for an extended period of time, and if left for too long, it can start to rust out the inside of the tank and the drain valve can become clogged with rust or start to corrode. You should be draining the tank each time you use your air compressor to stop this from happening. This is a very quick and simple repair. Use a wrench to remove the old drain valve, and thread the new one into place by hand.

Installation Instructions

Steven from SMITHS STA, AL

Wouldn't hold air in tank.

Took old drain valve out and replaced with new one. Read more...

Carbon Brush Set CB-303

$10.85

Fix Number: FIX10156649
Manufacturer Part Number: CB303

The carbon brush is used on a variety of tools and are commonly replaced because they wear out easily with time and use. If your brush is worn out it can affect the motor from working properly and reduce electric braking. Tip: to check if the brush is worn out, inspect the wire lead for cracks, burns and other damage. Refer to the diagram provided by the manufacturer for further installation instructions. *Please note: This part is sold individually. This assembly includes a carbon brush, spring and holder.

Watch the install video

Carbon Brush Set

$6.36

Fix Number: FIX10156662
Manufacturer Part Number: CB440

The brush box kit fits a variety of cordless gardening tools. *Please note: This part is sold individually. This assembly includes a carbon brush, spring and holder. Due to friction, carbon brushes are common replacement parts. If the functioning of your motor changes and does not work, then check if the brush is worn out or inspect the wire lead for cracks, burns and other damage. Replacing the brush can restore the motor and its functions. Refer to the manual provided by the manufacturer for further installation instructions.

Watch the install video

Power Cord

$21.97

Fix Number: FIX10153834
Manufacturer Part Number: 664064-4

This is a power cord, and it is used with several power tools. It is made of a thick rubber that is tough, and insulated for a long life. It has two 18 gauge wires, and is 8 feet long. When removing your old cord, take note of the wire leads placements, and how they connect to the receptacle in the tool. You will have to attach the new cord similarly.

Installation Instructions

John from Hancock, MI

Did not come with grinding disc guard

While unit was unplugged I screwed clamp of guard around grinder. Read more...

Carbon Brush CB-124 (Set of 2)

$7.83

★★★★★

1 Review

Fix Number: FIX10156640
Manufacturer Part Number: CB124

Carbon brushes are needed to conduct electricity to the armature through the commutator. The brushes are continuously rubbing against the rotating commutator, so will wear down over time, and will need to be replaced. If you are experiencing excessive sparks, this can also be caused by a damaged armature, so it is best to check it at the same time. This part includes two carbon brushes, which need to be replaced at the same time.

Power Tool Power Cord

$23.43

★★★★★

1 Review

Fix Number: FIX10153842
Manufacturer Part Number: 664265-4

This power cord is for power tools. Unplug the power tool before installing this part. Wear work gloves to protect your hands.

Carbon Brush Set CB-204

$26.23

Fix Number: FIX10156646
Manufacturer Part Number: CB204

This is a set of two OEM carbon brushes with wire leads and brush springs. To ensure your motor is running efficiently, it is important to continually inspect the carbon brushes, as they are a common wear part. If they are damaged this will greatly affect the performance of the motor. If burns or cracks are present, it is advised to inspect the armature as well.

Makita Parts

Popular Makita Parts

Installation Instructions

Installation Instructions

Makita Appliance Types

Popular Makita Models

Makita Parts

Start With Your Model Number

Popular Makita Parts

Installation Instructions

Installation Instructions

Makita Appliance Types

Popular Makita Models