Hotpoint Parts

Start With Your Model Number

Need help finding your model number?
Find Parts Fast
Guaranteed Fit
Repair Videos
Fix.com search
Hotpoint Appliance Parts
Shop By Appliance Type

Popular Hotpoint Parts

Watch the install video
Drum Bearing Slide - Green (Sold individually) – Part Number: WE1M1067
Drum Bearing Slide - Green (Sold individually)
$14.28
In Stock
★★★★★
★★★★★
2 Reviews
Fix Number
FIX6447706
Manufacturer Part Number
WE1M1067
This single drum bearing slide is an OEM approved replacement part for dryers. It can also be known as a bearing drum slide, pad, or glide. The slides attach to the inner most slots on the front bearing. As the dryer rotates, the drum bearing slides help to support the front of the drum. If your appliance becomes noisy, is not drying properly, or leaves marks on clothes, it may be time to replace it. If you are replacing one slide, we recommend replacing the other slide at the same time, as they deteriorate at a similar rate. You will need to order 2 of these parts as there are 2 in each dryer. It is approximately 2.6-inches deep, 0.06-inches in height, and 0.5-inches wide. This part is denoted as being green in the title, however users and technicians have noted it is actually gray in color.
Fixes these symptoms

Installation Instructions

Donald L. from Belmont, MA
Dark marks on clothing; clothing sticking between drum and front panel
Others with the same problem of dark marks on clothing suggested replacing the white and the grey drum slides that slip into the front drum bearing unit. When I open up the dryer, I did find that both the white and grey drum slides on one side of the front drum bearing piece had completely worn away, and some of the drum bearing piece was also worn away. I had decided in advance to order both white slides, both grey slides, a new felt seal, and the front drum bearing piece. Possibly I could have reused the old front drum bearing, but the replacement was cheap enough. Three bits of advice: 1) if you replace the felt seal, make sure you get it tucked behind the clips on the door panel; 2) if you replace the front drum bearing piece, once you have the dryer put back together, reach up and pull the plastic drum bearing toward you to be sure it is fully snapped into place; 3) after you replace the slides or felt, the drum will make mild rubbing noises as it turns, so run the dryer with no heat for about 30 minutes to seat the parts. Read more...
Watch the install video
Drive Belt – Part Number: WE03X29897
Drive Belt
$36.10
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX16542496
Manufacturer Part Number
WE03X29897
This 89.5-inch drive belt is for dryers. It has a 4-rib design on the inside for a better grip. If comparing the size of your current belt to the new one, keep in mind that a small amount of stretching and contortion will occur over time, and this belt will fit despite small inaccuracies. You will find this part wrapped all the way around the dryer drum, around a tension pulley, and around the drive motor pulley. This allows the parts to work together to spin the drum as the motor rotates. A common symptom of a broken drive belt is a drum that will not turn. This part is prone to wear and tear over time and will likely stretch or become brittle, leading to complete breakage of the part. The drum cannot spin without a drive belt, so it needs to be replaced immediately. For this repair, we recommend wearing work gloves to protect your hands from sharp edges, disconnect the power, remove the main panel, and access the motor drive to secure the new belt in place.
Fixes these symptoms
  • Drum Not Spinning
  • Heat stays on after drum has stopped
  • Noisy
  • See more...

Installation Instructions

Nae from BRENTWOOD, TN
The dry was making a whining sound. Very loud.
I followed all the video on the website with all the parts I had purchased. Very easy. Just make sure you unplug the dryer first. Thank you, Read more...
Watch the install video
Drum Bearing Slide - White (Sold individually) – Part Number: WE1M504
Drum Bearing Slide - White (Sold individually)
$18.57
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX755842
Manufacturer Part Number
WE1M504
This single drum bearing slide attaches to the outer-most side of the bearing. This part is also sometimes referred to as a drum slide, drum glide, or drum pad. It provides support to the front of the drum as it rotates. They are approximately 3-inches long, 1 inch wide and made from a durable white plastic. If your appliance starts making unusual sounds, is not drying clothes properly, or leaves marks on clothes, it may be time to replace this part. The dryer has 2 slides, which we recommend replacing at the same time, as they tend to wear out at the same rate. You will need to order 2 of this part to replace both drum bearing slides, since it is sold individually. Before you begin this repair, be sure to disconnect the power to the dryer.
Fixes these symptoms

Installation Instructions

Donald L. from Belmont, MA
Dark marks on clothing; clothing sticking between drum and front panel
Others with the same problem of dark marks on clothing suggested replacing the white and the grey drum slides that slip into the front drum bearing unit. When I open up the dryer, I did find that both the white and grey drum slides on one side of the front drum bearing piece had completely worn away, and some of the drum bearing piece was also worn away. I had decided in advance to order both white slides, both grey slides, a new felt seal, and the front drum bearing piece. Possibly I could have reused the old front drum bearing, but the replacement was cheap enough. Three bits of advice: 1) if you replace the felt seal, make sure you get it tucked behind the clips on the door panel; 2) if you replace the front drum bearing piece, once you have the dryer put back together, reach up and pull the plastic drum bearing toward you to be sure it is fully snapped into place; 3) after you replace the slides or felt, the drum will make mild rubbing noises as it turns, so run the dryer with no heat for about 30 minutes to seat the parts. Read more...
Watch the install video
Lint Filter – Part Number: WE03X23881
Lint Filter
$41.03
In Stock
★★★★★
★★★★★
7 Reviews
Fix Number
FIX11763056
Manufacturer Part Number
WE03X23881
This Lint Filter is a genuine OEM part for your clothes dryer. The Lint Filter can be used with both electric and gas models. Proper air flow is essential to the operation of the dryer, and the lint filter helps prevent debris from getting into your ducts and causing obstructions. Regular cleaning of this part is essential to prevent fires and can help your laundry dry more quickly. It may be time to replace the filter if the casing is cracked or the screen is ripped, or it is taking a long time for your laundry to dry. Installation is very easy and no tools are required; simply remove the old filter (just like you would to clean it) and insert the new one in its place.
Fixes these symptoms

Installation Instructions

Georgia from HOT SPRINGS, VA
Replacement
Just popped it in the opening. Read more...
LOWER SPRAY ARM – Part Number: WD22X33499
LOWER SPRAY ARM
$19.70
In Stock
★★★★★
★★★★★
2 Reviews
Fix Number
FIX17137081
Manufacturer Part Number
WD22X33499
Fixes these symptoms
  • Leaking
  • Noisy
  • Not cleaning dishes properly
  • See more...

Installation Instructions

Kevin from SUN CITY WEST, AZ
Rhythmic noise from bottom spray, arm, banging on heat element
Replace bottom spray arm assembly Read more...
Watch the install video
LOWER RACK ROLLER – Part Number: WD12X26146
LOWER RACK ROLLER
$13.11
In Stock
Fix Number
FIX16217024
Manufacturer Part Number
WD12X26146
The roller helps the lower rack of your dishwasher to smoothly slide in and out of your appliance. A broken or worn roller wheel can make it clunky or difficult to get the rack in and out of the dishwasher, and the part should be replaced. The rollers are sold individually, however there are four in total in your dishwasher. You may want to replace all at the same time to ensure they have even wear. Replacing a broken roller is a simple job and may require the use of a flat blade screwdriver. Remove the entire lower rack from your dishwasher and place it on a suitable work surface. Release the tabs to open the cover on the roller assembly, using the screwdriver if necessary to pry them open. Pull the damaged wheel off the assembly and push the new one into place. Reattached the cover and place the rack back into the bottom of your dishwasher. The lower rack should now easily glide in and out. These rollers are genuine OEM parts that measure approximately 1.5 inches in diameter and are charcoal in color.
Watch the install video
Front Drum Bearing – Part Number: WE3M26
Front Drum Bearing
$34.10
In Stock
★★★★★
★★★★★
2 Reviews
Fix Number
FIX960316
Manufacturer Part Number
WE3M26
Located on the inside of the dryer front panel, the front drum bearing helps your appliance to operate as quietly as possible. It allows the front of the drum to glide smoothly on the felt seal of the front panel when the drum is rotating. This manufacturer-approved part is made of a durable white plastic and measures approximately 9 inches by 20 inches. If your dryer makes a continuous banging noise while it is powered on, it is likely that the drum bearings need to be replaced. Keep in mind that the drum slides should be replaced at the same and will need to be purchased separately (the front drum bearing holds 4 glides), as this part includes the bearing only.
Fixes these symptoms

Installation Instructions

Donald L. from Belmont, MA
Dark marks on clothing; clothing sticking between drum and front panel
Others with the same problem of dark marks on clothing suggested replacing the white and the grey drum slides that slip into the front drum bearing unit. When I open up the dryer, I did find that both the white and grey drum slides on one side of the front drum bearing piece had completely worn away, and some of the drum bearing piece was also worn away. I had decided in advance to order both white slides, both grey slides, a new felt seal, and the front drum bearing piece. Possibly I could have reused the old front drum bearing, but the replacement was cheap enough. Three bits of advice: 1) if you replace the felt seal, make sure you get it tucked behind the clips on the door panel; 2) if you replace the front drum bearing piece, once you have the dryer put back together, reach up and pull the plastic drum bearing toward you to be sure it is fully snapped into place; 3) after you replace the slides or felt, the drum will make mild rubbing noises as it turns, so run the dryer with no heat for about 30 minutes to seat the parts. Read more...
Watch the install video
Upper Rack Assembly – Part Number: WD28X30219
Upper Rack Assembly
$82.22
In Stock
Fix Number
FIX16618975
Manufacturer Part Number
WD28X30219
This dishrack is for dishwashers. The dishrack holds the dishes in place during the dishwashing cycle. Follow the instructions in the manual when installing this part.
Fixes these symptoms
Watch the install video
Refrigerator Ice and Water Filter – Part Number: MWFP
Refrigerator Ice and Water Filter
$73.01
In Stock
Fix Number
FIX8746144
Manufacturer Part Number
MWFP
This is an OEM replacement water filter for your refrigerator. The manufacturer suggests replacing this filter every 6 months or 300 gallons of water. If not replaced regularly, you will risk contaminants getting into your water, and poor performance of your water dispenser and/or icemaker. This filter has a twist and lock design, making the replacement of this part very simple and tool-free. Please note that the manufacturer has updated this filter, so if this is the first time installing it you may require an adapter, which is sold separately. If your model has a reset button, do not forget to hold it down for a few seconds to reset the indicator once you?ve replaced this part. Adapter, PartSelect #: PS220347
Fixes these symptoms
  • Ice maker dispenses too little ice
  • Ice maker not making ice
  • Ice maker won’t dispense ice
  • See more...

Installation Instructions

saul from wylie, TX
the fridge would not stay cool
Replace the termostat and temp sensor for those two you have to cut and splice new wires. And the water filter easy twist off and twist back on for the heater and braket assembly it was pull out old and place new maybe hour long job Read more...
Gasket – Part Number: WD08X21894
Gasket
$8.54
In Stock
Fix Number
FIX11700870
Manufacturer Part Number
WD08X21894
This is a genuine OEM replacement gasket for your dishwasher, that measures approximately 22 inches long and is made of plastic. It is found at the bottom of the inside panel of your dishwasher door. The purpose of the gasket it to provide a tight seal at the bottom of the dishwasher so that water does not leak out while the appliance is operating. If your dishwasher is leaking, you should inspect the gasket for signs of damage and replace it if worn out. Please note that gaskets for sealing around the tub are sold separately. Basic tools are needed for this repair, including a pair of pliers to help with removal of the old gasket. Depending on your model, you may need to remove door panels to access the gasket which would require a Philips screwdriver.
Fixes these symptoms

Hotpoint Appliance Types

Popular Hotpoint Models

View More
+