OEM Craftsman Parts & Accessories

Lawn Tractor Mandrel Assembly

$48.56

★★★★★

1 Review

Fix Number: FIX12087499
Manufacturer Part Number: 587819701

Installation Instructions

Terrence from LORENA, TX

Blade mandrel replacement

1. Remove mower deck.
2. Remove mower blade from defective mandrel.
3. Clean caked up grass from underside of mower deck.
4. Remove belt pulley from top of defective mandrel.
5. Remove four bolts fastening defective mandrel to deck. Note: bolts will most likely shear - make sure you have new ones.
6. Install new mandrel to deck using four new self-tapping bolts.
7. Reinstall mower blade to new mandrel assembly.
8. Reinstall belt pulley to new mandrel assembly.
9. Reinstall mower deck to tractor. Read more...

Bearing

$6.21

Fix Number: FIX9006914
Manufacturer Part Number: 532009040

This is a premium-quality OEM front wheel flange bearing (sometimes called bushing) commonly used in riding lawn mowers. They are used to keep the wheel held in place securely. It is sold individually but two are needed for each front wheel. It is recommended that they be replaced at the same time. Install this part with the flat side facing the grease zerk in the rear side of the wheel.

Watch the install video

Engine Fuel Filter

$4.99

Fix Number: FIX9285148
Manufacturer Part Number: 530095646

This fuel filter is for lawn and garden equipment engines. Fuel filter cleans the fuel before it reaches the carburetor. Work in a well-ventilated area when installing this part. Drain the fuel tank and disconnect the spark plug wire before beginning the repair.

Fixes these symptoms

Engine stops after a few seconds or minutes
Will Not Start
See more...

Installation Instructions

Aaron from BALTIC, OH

Wouldn’t start

Replaced fuel line and filter. Also replaced diaphragms, screens, float, needle and gaskets. It then started but wouldn’t keep running. I had to back out fuel air mix needle completely and spray carb cleaner in these holes. It then ran perfectly. Make sure you count the rounds they are backed off before removing. Read more...

Ring Klip Number T5304-75

$3.99

Fix Number: FIX9143890
Manufacturer Part Number: 812000029

This manufacturer-approved ring clip is found in various lawn and garden equipment models. A ring clip is used as a fastener that secures components or assemblies onto a shaft or housing (such as part of a mower wheel or steering assembly). When it is installed, the part that is visible acts as a shoulder, holding the specific component or assembly together. This very small metal ring clip (approximately 1-inch by 1-inch) is sold individually.

Wheel and tire assembly (Front Drive Wheels)

$27.67

★★★★★

3 Reviews

Fix Number: FIX11971248
Manufacturer Part Number: 583719501

This is a genuine OEM sourced replacement part is used with walk behind lawn mowers. This is the drive wheel which has plastic gears on the inside. It is designed to be driven by a pinion gear which is sold separately. If the wheel is broken or damaged it should be replaced to ensure smooth ride and consistent cut of the grass. Includes one (1) plastic wheel.

Cap Axle Black 1 50 x 1 00

$3.99

Fix Number: FIX9007667
Manufacturer Part Number: 532104757

This is an OEM axle cap for lawn tractors and is sold individually. It stops debris from getting into the wheel hub and axle. This axle cap is prone to wear and tear and should be replaced when it is goes missing or appears damaged. No tools are necessary for this easy repair, simply locate the cap axle on the rim of the wheel and remove.

Wheel

$4.99

Fix Number: FIX12630280
Manufacturer Part Number: 589527301

Wheel.gage.half.spoked

Bolt and Washer Assembly

$8.71

Fix Number: FIX9020856
Manufacturer Part Number: 532193003

This manufacturer-approved bolt and washer assembly is for lawn tractors. Wear work gloves to protect your hands when installing this part.

Blade Mower Hi Lift

$23.87

★★★★★

1 Review

Fix Number: FIX9017804
Manufacturer Part Number: 532405380

This is a manufacturer-approved high quality replacement blade for a lawn tractor and is sold individually. It is used on 46-inch decks, and measures approximately 22-1/2 inches long and 2-3/4 inches wide. This blade is a high-lift blade (2-in-1 blade), meaning it is designed with curved tips that lift grass clippings up and out through the discharge chute into a grass bag (if applicable). By replacing a dull, bent, or damaged blade, this will ensure a better quality cut. For this repair, you will need a wrench to remove the blade bolt, and we recommend wearing gloves to protect your hands.

Shear Pin, .25

$3.99

Fix Number: FIX9110822
Manufacturer Part Number: 738-04124A

Designed for use in MTD, Yard Machine, Troy-Bilt, Yard-Man, and Craftsman machines, this OEM approved Shear Pin fits a variety of models. For full compatibility, please see the "Model Cross Reference List" below. This is a shear pin for your lawn and garden equipment, most commonly your snow blower. It is designed to snap if your auger gets jammed or clogged, to protect your snow blower from further damage. Because this part is meant to snap at a certain point of pressure, it is a commonly replaced part in snow blowers. Consequently, we recommend keeping a spare on hand. This Shear Pin is approximately 1.75" long, and is sold individually.

Craftsman Parts

Popular Craftsman Parts

Installation Instructions

Installation Instructions

Craftsman Appliance Types

Popular Craftsman Models

Craftsman Parts

Start With Your Model Number

Popular Craftsman Parts

Installation Instructions

Installation Instructions

Craftsman Appliance Types

Popular Craftsman Models