OEM Black and Decker Parts & Accessories

Cover

$6.19

Fix Number: FIX12443187
Manufacturer Part Number: 385022-03N

This is an OEM replacement cover for a string trimmer or edger. The cover holds the spool and line securely inside the spool housing. If this part has cracked or damaged, it will need to be replaced. When removing this part, make sure the trimmer is unplugged, release the tabs by pressing them down with your fingers, and pull it straight off. Place the new cover on by simply snapping it into place. This plastic cover is sold individually.

Router Motor Brush

$4.99

Fix Number: FIX10116510
Manufacturer Part Number: N031634

This motor brush is for routers. The motor brush transfers electric current to the spinning armature in the motor. Unplug the router before installing this part.

Brush and Spring

$8.86

★★★★★

1 Review

Fix Number: FIX10166057
Manufacturer Part Number: 145323-06

This carbon brush and spring kit includes a carbon brush, wire lead, and a spring. The parts fit a variety of tools such as saws. If you notice your motor is running poorly or is intermittent, then check the brush for damage, cracks, and burns. It is common to replace the brushes repeatedly as they easily wear off from friction and use. Tip: remember to inspect your armature for burns and cracks when replacing your carbon brushes. This will help identify larger motor problems. This part measures to 3/4 inches in length, 1/2 inches in width, and the 1/4 inches in thickness. Refer to the manual for installation instructions and a list of the parts included.

Sander Pad Hook and Loop (Velcro) - 5 Inch

$27.93

Fix Number: FIX10106353
Manufacturer Part Number: 151281-08

The 151281-08 Pad is used to hold 5 inch Hook and Loop sandpaper with 8 vacuum holes. Over the past few years the popularity of Hook and Loop paper has grown because of the ease of changing sandpaper when needed. Over that of the PSA (Pressure Sensitive Sandpaper) Applying too much pressure on the sander may cause premature wear on the Hook and Loop pad. When a pad needs to be replaced, simply remove the three screws that hold the pad to the sander, then replace it with a new pad.

Watch the install video

Power Cord

$17.56

★★★★★

1 Review

Fix Number: FIX10169875
Manufacturer Part Number: 330072-98

This power cord is used for power tools and some of the following tools: electric drills, reciprocating saws, jig saws, biscuit joiners, and routers. The power cord is made for double insulated tools and is a two-wire cord with two prongs, but it does not need a ground wire. If there are cuts in the cord insulation, intermittent power during operation, or damaged and bent prongs, then replacing the power cord will solve the problem. The tools needed for this repair are a Phillips screwdriver, small screwdriver, wire cutters/strippers, crimping tool, and terminal (ring or spade). Repair tip: During installation, remember that new cord wires must go correctly into wire terminals. Also, to avoid pinching when the tool case is put back into place, remember to route cord and wires in the right path.

Installation Instructions

John from Hancock, MI

Did not come with grinding disc guard

While unit was unplugged I screwed clamp of guard around grinder. Read more...

Watch the install video

Drain Valve

$4.99

★★★★★

1 Review

Fix Number: FIX10049094
Manufacturer Part Number: N286039

This is a single OEM drain valve for an air compressor. A drain valve is a small device that is usually located at the bottom of the compressor air receiver. The drain valve can be opened or closed, and this allows water to exit the tank. Water builds up if air is left in the tank for an extended period of time, and if left for too long, it can start to rust out the inside of the tank and the drain valve can become clogged with rust or start to corrode. You should be draining the tank each time you use your air compressor to stop this from happening. This is a very quick and simple repair. Use a wrench to remove the old drain valve, and thread the new one into place by hand.

Installation Instructions

Steven from SMITHS STA, AL

Wouldn't hold air in tank.

Took old drain valve out and replaced with new one. Read more...

Watch the install video

Grinder Motor Brush

$7.87

Fix Number: FIX10106782
Manufacturer Part Number: 445861-25

(Sold Individually) This motor brush is for grinders. The motor brush transfers electric current to the spinning armature in the motor. Unplug the grinder before installing this part. Wear work gloves to protect your hands.

Watch the install video

Blade Adapter Ring

$4.99

★★★★★

2 Reviews

Fix Number: FIX10166690
Manufacturer Part Number: 152636-00

This is an authentic adapter ring used to mount the saw blade to your miter saw. It is sold as an individual part. Standard 12-inch saw blades have a 1-inch arbor hole, while most miter saw arbors are 5/8 of an inch. This adapter ring is placed on the blade hole and over the arbor so you can use a 12-inch blade. This part is prone to wear and tear, which will make the blade unbalanced, signalling that it should get replaced.

Leg Catch

$6.59

Fix Number: FIX9927406
Manufacturer Part Number: 242416-00

This is a single OEM leg catch for workbenches. This part holds the leg on the workbench in the down position and locks it into the correct position. When it is released, the leg can raise back into the up position. If the legs of your workbench are wobbly or will not lock in place properly, a damaged leg catch is the likely culprit.

Installation Instructions

Roger from LIVONIA, MI

Replace broken leg catch

Punched out rod holding broken catch. Took it to bench grinder to taper ends when putting it back together after placing new leg catch on it. Tapering made it much easier on reinstall. Read more...

Carbon Brush (Sold Individually)

$10.69

Fix Number: FIX10176277
Manufacturer Part Number: 5140011-85

This is a single carbon brush with a spring. Carbon brushes are what supply electricity to the armature. They are known to wear due to constant rubbing against the commutator, so it should not be a concern if they are in need of a replacement. They should be inspected regularly, especially if your power tool is not functioning properly. A worn brush can cause excessive sparks, however a damaged armature can also cause sparks, so you will need to inspect both parts. This is a simple repair that should only take a few minutes. You will need to remove the brush caps, and then align the new carbon brush in the holder with the tabs. You will need a screwdriver to secure the cap.

Black and Decker Parts

Popular Black and Decker Parts

Installation Instructions

Installation Instructions

Installation Instructions

Black and Decker Appliance Types

Popular Black and Decker Models

Black and Decker Parts

Start With Your Model Number

Popular Black and Decker Parts

Installation Instructions

Installation Instructions

Installation Instructions

Black and Decker Appliance Types

Popular Black and Decker Models