Freezer Hardware

Fix Number

FIX963756

Manufacturer Part Number

WR02X12008

The evaporator fan grommet is used to provide a cushion between the fan motor and the motor mounting bracket in your freezer. This genuine OEM part is about one inch in diameter and is red in color. It is part of the motor assembly found behind the evaporator fan cover at the back of your freezer. If the fan has become quite noisy, it may be time to replace the grommet. To complete this repair, you will need to remove everything from the freezer including the ice tray, the fan cover, freezer floor, evaporator cover, and the fan motor assembly. The tools you will need for this job include a pair of needle nose pliers, a Philips screwdriver and a small flat blade screwdriver, along with a 1/4-inch and a 5/16-inch nut driver. Please ensure that you disconnect the power supply to your fridge before you begin this repair.

Fix Number

FIX11746909

Manufacturer Part Number

WP9703438

Sometimes referred to as a retaining clip, the retaining ring is used to hold the drum support roller onto the shaft in your dryer. The clip may need to be replaced if you find that your dryer is noisy while tumbling or will not tumble at all. The retaining clip can also be used with stand mixers, to hold the pinion gear to the agitator shaft. This genuine OEM part is made entirely out of metal and measures approximately half an inch in diameter.

Fix Number

FIX11757021

Manufacturer Part Number

WPW10661886

This authentic OEM part is a mounting screw for the door handle on your refrigerator. If the door handle is loose or you are having issues opening or closing the door, a new mounting screw may solve these issues. Please note that the screw is sold individually, so if you need to replace more than one you will need to order the appropriate quantity.

★★★★★

★★★★★

1 Review

Fix Number

FIX8752913

Manufacturer Part Number

MJB63190001

This part includes a single mounting bolt needed to secure the door handle to your refrigerator. This part is commonly replaced because the handle has started to loosen. Try tightening the screw first, and if that does not solve the problem, this mounting bolt likely requires replacement. Please note that your handle has a few of these screws and they tend to wear at the same rate, so we recommend having one or two extra on-hand.

Fix Number

FIX284979

Manufacturer Part Number

WR02X10540

This genuine OEM replacement part is a bumper for your refrigerator. The bumper is made of orange rubber and measures less than half an inch in diameter. The bumper is used to prevent the fan motor from scraping against the side bracket in the evaporator fan motor assembly. You can find the bumper behind the evaporator fan cover in the freezer. If your fridge or freezer is noisy, it is likely that the bumper has worn down and will need to be replaced.

Fix Number

FIX1526032

Manufacturer Part Number

240521303

This small, Phillips-head screw works with your refrigerator/freezer. It screws in to the freezer door and connects to the door handle. This part is made of stainless steel and is sold individually. This is an OEM part sourced directly from the manufacturer.

Fix Number

FIX11743743

Manufacturer Part Number

WP681249

Sold individually.

Fix Number

FIX11746840

Manufacturer Part Number

WP90767

This is a multi-use screw and can be used on a variety of appliances. The measurements of the screw are: 8/18 x 3/8. *Please note: the screw is sold individually. Refer to the manual provided by the manufacturer for further repair guidance.

Fix Number

FIX1525803

Manufacturer Part Number

218755504

Sold individually. This is a genuine part. The handle mounting shoulder screw (no.10 ab) is made for use with many refrigerators. The metal screw helps to fasten the handle assembly to the outer door panel. The handle mounting shoulder screw is sold individually. For the repair, you will need a pair of pliers.

Fix Number

FIX1015726

Manufacturer Part Number

WR02X12149

This OEM compression ring is used to hold the evaporator fan motor in place. Signs that you may need to replace the compression ring are if the fan is noisy, or your fridge or freezer are too warm. We recommend replacing both the compression ring and the evaporator fan grommet at the same time. The evaporator fan motor is found at the back of the freezer compartment, and you will need a Phillips screwdriver to remove the cover concealing the fan. A small flat blade screwdriver may be needed to remove the compression ring from the fan. Please be sure to disconnect the power supply to your fridge before beginning this repair.