Models
>
K5SS
K5SS KitchenAid Mixer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for K5SS
Viewing 3 of 3Manuals & Guides for K5SS
Click to downloadKeep searches simple, eg. "belt" or "pump".
$20.97
This part includes one worm gear for a stand mixer. It measures approximately 1.5-inches in diameter and is sourced directly from the manufacturer. The worm gear is responsible for turning the planeta...
In Stock
Order within the next 11 hrs and your part ships today!
$7.87
Sometimes referred to as a retaining clip, the retaining ring is used to hold the drum support roller onto the shaft in your dryer. The clip may need to be replaced if you find that your dryer is nois...
In Stock
Order within the next 11 hrs and your part ships today!
$13.51
This genuine OEM part is a motor brush for your stand mixer. The brush is sold individually, however, there are two motor brushes on your mixer, and we recommend replacing both at the same time, as th...
In Stock
Order within the next 11 hrs and your part ships today!
$27.56
This flat beater is used on stand mixers. It is dishwasher safe, however, should only be washed in the upper rack. The Flat Beater is used to mix batters and light doughs. Should the coating become da...
In Stock
Order within the next 11 hrs and your part ships today!
In Stock
Order within the next 11 hrs and your part ships today!
$27.32
This wire whip attaches to your stand mixer and is used for whipping food products. It is made of metal wire and is one of several attachments that you can add to your mixer. If you attempt to start y...
In Stock
Order within the next 11 hrs and your part ships today!
$23.37
This part is used with the stand mixers attachments, as well as to hold the end cap to the front of the mixer.
In Stock
Order within the next 11 hrs and your part ships today!
In Stock
Order within the next 11 hrs and your part ships today!
In Stock
Order within the next 11 hrs and your part ships today!
$64.99
This Stand Mixer Gear Grease lubricates the moving parts of the stand mixer.
In Stock
Order within the next 11 hrs and your part ships today!
In Stock
Order within the next 11 hrs and your part ships today!
In Stock
Order within the next 11 hrs and your part ships today!
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.
Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Rita
February 24, 2022
I am missing the part to hold the noodle maker in place. I can't find the part on any section listed here.
For model number K5SS
Hello Rita, thank you for writing. We believe you are looking for PartSelect Number FIX11769354. You may view it on the website as item #2. We hope to hear from you soon.
Was this helpful?
Thank you for voting!
Related Parts:
Common Problems and Symptoms for K5SS
Viewing 2 of 2Noisy
Fixed by these parts
How to fix it
Touchpad does not respond
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from Minot, ND
- Parts Used:
- WP9709276
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Speed Control Lever KNOB BROKEN
Pulled the Knob off of the new Lever then pressed it on the old Lever. I had to order the whole lever because it was the part nearest the knob in the illustrated parts break-down. I RECOMMEND THAT THE KNOB BE ADDED TO THE ILLUSTRATED PARTS BREAK-DOWN.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from Shirley, MA
- Parts Used:
- WPW10112253
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
motor would run but mixer wouldn't operate: broken worm gear
My girlfriends' stand mixer failed when the accessory drive cap fell into the mixing bowl and jambed the beater, spliting the worm gear. The teeth on this gear are made of nylon and are molded to an aluminum center. This part is designed to fail in situations like this, saving the more expensive transmission parts. Following a repair manu
... Read more
al I found online, I first removed the rear cover and pulled out the cord strain relief out from the base. Next I removed the drip cup from around the base of the planetary drive. I then used a pin punch to drive out the pin holding the planetary to the center shaft and removed the planetary. The unit was then inverted and I removed 4 screws holding the bottom cover to the gear case, and the 5 screws from around the planetary drive. The bottom cover was then lifted off. Three screws holding the worm gear bracket in place were then removed and the worm gear assembly lifted out. A small pin holds the worm gear to the shaft. I drove this out with a small pin punch and the shaft and worm gear were then removed. There is also a thrust washer on this shaft, and it's location is important. Make a note for re-assembly. The new gear was installed and the entire process reversed for re-assembly. A successful repair completed! My girlfriend would have replaced this $200 appliance, but I was able to repair it for less than $30 including shipping.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Minden, NV
- Parts Used:
- WPW10380496, WP240309-2
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Mixer was making clunking sounds and shaking
I removed screws in a sequence that I felt wouldn't further damage the mixer until I had it completely unassembled. When I found the broken worm gear, I went online to find a part. I found an exploded view, but the part numbering was old, and the salesperson couldn't tell me what the worm gear and bracket assembly consisted of, as I only
... Read more
wanted the worm gear. After trying to drive the pin out of the assembly, and failing, I decided to back online and see if anyone else had a photo of the assembly. Luckily (and wisely) PartSelect,com did and that answered any questions I had. The price was better, too. Reassembly of the mixer was a cinch with the exploded view. It's working like new, and we're hoping for another 35 years of service from it! Thanks.
Read less
Was this instruction helpful to you?
Thank you for voting!